濟南手板模型加工的制造工藝

Manufacturing process of Jinan hand board model

1、通過手板模型加工設備依據程序設定的途徑，在產品的原資料的基礎上進行改動，得到手板模型加工的雛形。

1. The prototype of the hand model processing is obtained by modifying the hand model processing equipment based on the original data of the product according to the way of program setting.

2、手藝處理。在手板模型加工的雛形出來之后，樣件的外觀會有一些毛刺以及邊角剩余的部分，工作人員應該用砂紙磨平，使得手板模型加工的外觀變得潤滑精美。

2. Process. After the prototype of the handboard model processing comes out, the appearance of the sample will have some burrs and the remaining parts of the edges and corners. The staff should use abrasive paper to smooth it, so that the appearance of the handboard model processing becomes smooth and beautiful.

3、鐳雕，即是用激光技術打掉樣件外觀的油漆，使樣件的一部分方位透光。

3. Laser carving is to use laser technology to remove the paint on the surface of the sample, so that part of the sample can be exposed to light in all directions.

4、氧化，即陽極處理，是行使電解的作用，因為處理過后構成的氧化的耐蝕性差、硬度低建網站費用，因而工藝進程中很少運用。

4. Oxidation, that is, anodic treatment, is used for electrolysis. Because the oxidation formed after treatment has poor corrosion resistance and low hardness, it is rarely used in the process.

5、拉絲，就是在鋁合金的外觀拉出一條條細痕，如許的處理會使樣件的質感更好。

5. Wire drawing is to draw fine lines on the appearance of aluminum alloy. Such treatment will improve the texture of the sample.

斷定選用手板模型加工的加工內容，斷定工件的裝置基面、加工基面、加工余量等，以充分發揮手板模型加工功率為意圖來組織加工工序。關于復雜零件來說，因為加工進程中會發生熱變形，淬火后會發生內應力，零件卡壓后也會變形等多種原因，故全部工序很難在一次裝夾后完結，這時能夠考慮兩次或多次裝夾。

Determine the processing content of the handboard model processing center, determine the device base plane, processing base plane, processing allowance, etc. of the workpiece, and organize the processing process with the intention of giving full play to the power of the handboard model processing center. For complex parts, due to various reasons such as thermal deformation during processing, internal stress after quenching, and deformation after clamping, it is difficult to complete the whole process after one clamping. At this time, two or more clamping can be considered.

手板模型加工工序時應本著由粗漸精的準則。首要組織重切削、粗加工，去掉毛坯上的加工余量，然后手板模型加工工精度要求不高的內容。選用大流量的冷卻方法，為削減加工時發生的大量熱量對手板模型加工精度的影響，為進步刀具耐用度，需活躍選用大流量的冷卻方法。您有需求就來我們網站http://m.csguangliang.com進行咨詢吧！

The processing process of hand model should follow the principle of "from rough to fine". First, re-cutting and rough machining shall be organized to remove the machining allowance on the blank, and then the manual model shall be processed for the content with low accuracy requirements. The cooling method with large flow rate shall be selected. In order to reduce the impact of a large amount of heat generated during processing on the processing accuracy of the hand model, and to improve the tool durability, the cooling method with large flow rate shall be actively selected. Come to our website if you need http://m.csguangliang.com Consult!